Microfreak/Preset/286 Driftsynchros

• Notes

  • SawX patch with a looping envelope closing the filter and expression increasing saw modulation.

  • Saved export and provenance

    • Saved export: September 28, 2026 MIDI Control Center user-bank archive, computer-bank slot 350, file 350-09282026 6h14-A350.mbp. The computer-bank slot differs from this page’s observed device slot.
    • The parameter payload matches Factory 3.0 and 6.0. This is an archived factory-equivalent baseline; it does not establish the instrument’s saved or unsaved state during a later session.

  • Oscillator

    • Model: SAWX. Saw Mod controls a modulus stage; Shape controls chorus amount; Noise adds phase modulation from subsampled white noise.
    • Saw Mod: 0.000.
    • Shape: 0.000.
    • Noise: 0.000.

  • Filter

    • Low-pass filter. Saved cutoff: 0.661; resonance: 0.234. Cutoff and resonance are normalized settings, not hertz or instrument display values.

  • Envelopes

    • Main envelope: attack 0.000, decay/release 0.621, sustain 0.000. Amp Mod is off; the envelope can still affect its matrix destinations.
    • Cycling Envelope mode: Loop. Stored RiseLvl 0.000, FallLvl 0.492, Hold 0.000, Amount 1.000. These are normalized stored fields; rise/fall times in milliseconds remain unverified.

  • LFO

    • Saw; clock sync on. Stored normalized rate: 0.148; division code: 8. The rate is not a hertz reading, and the musical division has not been converted.

  • Modulation matrix

    • Amounts use the signed normalized range −1…+1. The assignment destinations below resolve the saved Assign columns.
    • Cycling Envelope → Pitch: −0.001. A small envelope route changes pitch.
    • PRESSURE → Wave / Saw Mod: +0.357. Expression increases saw modulation.
    • Cycling Envelope → Cutoff: −0.904. The looping envelope strongly closes the filter.
    • LFO → Cutoff: −0.031. The saw LFO changes filter brightness.
    • PRESSURE → Cutoff: +0.021. Expression slightly opens the filter.
    • Cycling Envelope → Assign 1 → Cycling Envelope FallLvl: −0.378. The envelope modulates its own stored fall control.
    • ENV → Assign 1 → Cycling Envelope FallLvl: +0.120. The main envelope also changes that fall control.
    • All other saved matrix amounts are zero.

  • Performance and session context

    • Amp Mod is off, so the main envelope does not shape loudness through Amp Mod; it still changes the cycling envelope through the matrix. The looping envelope supplies the strongest filter movement.
    • Paraphonic mode is on in the saved export. The PRESSURE matrix row uses pressure or velocity according to the instrument’s global Utility setting; the export does not establish which expression source was used in the session.
    • GitP/A/Session/26/10/12-Mon references this sound. The session context does not identify which recording passages use it.

  • Evidence and interpretation

    • Base controls use normalized 0…1 values unless a stored choice code is shown; matrix amounts use −1…+1. These describe saved base settings, before modulation, and are not OLED percentages, hertz or milliseconds.
    • The saved-parameter inspector preserves the original fields. Oscillator interpretation assumes the documented firmware 5 layout; firmware is not detected from the export.
    • Matrix columns and assignments follow the Freakout live map and assignment decoder. Mode and waveform labels follow the MicroFreak Reader definitions.
    • Microfreak/UG/06 Dig Osc/03 Types/15 SAWX describes oscillator controls. Microfreak/UG/05 Connections/02 Matrix and Encoder/01 Sources and Destinations explains the matrix and expression row.